READ ENTIRE LABEL BEFORE APPLYING
DESCRIPTION AND USES
Rust-Oleum® Sierra Performance™ Beyond™ Acrylic Enamel is an industrial performance, low VOC, low HAP, very low odor, single component, water-based acrylic urethane.
This coating is designed for use on a primed or painted substrate. It is suitable for both interior and exterior applications. Suitable for doors, cabinets, trim, furniture, equipment, tanks, etc. The very low odor of this coating makes it ideal for use in schools, healthcare facilities, food service areas, office buildings, hotels or in any area where odors are an issue.
Beyond complies with USDA FSIS regulatory sanitation performance standards for food establishment facilities. This coating is impervious to moisture and easily cleaned and sanitized.
PRODUCT APPLICATION
SURFACE PREPARATION
ALL SURFACES: Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with Krud Kutter® Cleaner Degreaser, commercial detergent or other suitable cleaner. Rinse thoroughly with fresh water and allow to fully dry.
STEEL: Scrape and wire brush or power tool clean to remove loose rust, scale, and deteriorated coatings in accordance to SSPC-SP-2 Hand Tool Cleaning or SSPC-SP-3 Power Tool Cleaning. Steel substrates must be primed with MetalMax Primer. Two coats of primer must be used if the substrate was prepared by abrasive blast cleaning.
PREVIOUSLY COATED: Previously coated surfaces must be sound and in good condition. Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with Krud Kutter® Cleaner Degreaser, commercial detergent or other suitable cleaner. Rinse thoroughly with fresh water and allow to fully dry. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile. Beyond is compatible with most coatings, but a test patch is suggested.
APPLICATION
Apply only when air and surface temperatures are between 50-100°F (10-38°C) and surface temperature is at least 5°F above dew point.
TINTING
Beyond tint bases can be tinted with COLORTREND® PLUS™ 808, COLORTREND® 888, Rust-Oleum 2030 Water-based Colorants or other high quality water-based or universal colorants. This product contains zero VOCs before tinting. Adding colorants may add VOCs. If used at the recommended levels, the VOC will not exceed 100 g/l
TINT BASE MAXIMUM COLORANT
|
1-Gallon |
5-Gallon |
DESCRIPTION |
|
2 oz. |
10 oz. |
White Pastel Base |
|
4 oz. |
20 oz. |
Tint Base |
|
8 oz. |
40 oz. |
Deep Tint Base |
|
12 oz. |
60 oz. |
Accent Tint Base |
EQUIPMENT RECOMMENDATIONS
BRUSH: Use a good quality synthetic bristle brush.
ROLLER: Use a good quality 3/8” synthetic nap roller cover.
AIR-ATOMIZED SPRAY:
|
Method |
Fluid Tip |
Fluid Delivery |
Atomization Pressure |
|
Pressure |
0.055-0.070 |
12-16 oz./min |
40-60 psi |
|
Siphon |
0.055-0.070 |
--- |
40-60 psi |
|
HVLP (var.) |
0.043-0.070 |
8-10 oz./min |
10 psi at tip |
AIRLESS SPRAY:
|
Fluid Pressure |
Fluid Tip |
Filter Mesh |
|
2000-3000 psi |
0.013-0.017 |
100 |
CAUTION: Protect surrounding surfaces from over spray. Over spray can be wet or dry depending on height of work, weather, environmental conditions and application equipment. Wet over spray can adhere to unwanted surfaces. Dry over spray may be removed by wiping or washing. Always clean dry over spray from hot surfaces before fusing occurs as surface temperatures can be higher than the air temperature.
THINNING
If needed thin with water. Do not exceed 4 fluid ounces per gallon.
CLEAN-UP
Clean up with soap and water and dispose of all waste material in a proper manner and in accordance with local waste regulations. Consult with local environmental regulations for appropriate method of disposal and/or recycling of paint and empty container.
For chemical and corrosion resistance, see Rust-Oleum Industrial Brands Catalog (Form #275585).