READ ENTIRE LABEL BEFORE APPLYING
DESCRIPTION AND USES
RockSolid® Textured Clear Topcoat Floor Coating is an odor free Polycuramine coating designed for use on RockSolid Metallic and chip coated floors.
PRODUCT FEATURES
- Low odor and VOC Free
- 45 minute pot life
- Patented Burst Pouch Technology Pouch (Two part
- Burst Pouch Technology U.S. Patent Number 8,381,903 B2)
- No hot tire pickup
- Satin finish with fine texture
- Drive on in 24 hours
KIT CONTENTS
- 2 Polycuramine Burst Pouches
- 2 – ¼” Covers Roller
- Instructions
Items not supplied with the kit which need to be purchased separately:
- Roller Frame
- Extension Pole
- 3” Paint Brush
- Paint Tray
Other optional items that may be needed include:
- Heavy Duty Degreaser
- Concrete Patch and Repair
- Stiff Bristled Broom or Scrub Brush
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING PROJECT
SURFACE PREPARATION
Moisture Testing - New concrete should be allowed to cure for 30 days before application of any coating. If there is any doubt about the dryness of the concrete, conduct a test by simply taping a piece of 4 mil plastic sheet 2’ X 2’ on the bare concrete for 24 hours. Be sure to tape all four sides. After 24 hours, check the concrete for signs of moisture. The concrete substrate will be darker if damp. If moisture is found, allow additional drying time (10-14 days) and repeat the test.
Testing for Sealer - Check for curing compounds or other types of sealers by pouring a small amount of water onto the concrete. If water soaks in, the surface is suitable for coating. If water beads up on the concrete, the surface is not porous and a test application is warranted to ensure proper adhesion will develop. Sanding or mechanical abrading may be required if proper adhesion does not develop.
Previously Coated Floors - If the floor has been previously coated, you need to determine if the coating is well adhered to the surface. If it is, you can coat over the previous coating if you completely de-gloss the surface using 40-80 grit sandpaper and wipe the surface down with MEK solvent. Make sure to wear proper protective equipment and follow the manufacturer’s instructions.
For clear topcoat applications over newly coated surfaces, the coating will need to be dry to allow foot traffic. Do not walk of the coating while it is still tacky. Apply no earlier than 8-10 hours after coating with RockSolid Floor Coating and within 7 days. Ensure the surface is clean and dry prior to application.
Testing for Adhesion - With a razor knife, cut and X through the coating and down to the concrete. Apply a 5” piece of tape over the X and press down firmly. Completely remove the tape with one quick pull. If more than 25% of the taped area is removed, the original coating is not bonded well and needs to be removed chemically or mechanically with a grinder.
Loose/Damaged Concrete – If concrete is loose or chipped, the coating will not adhere properly. Repair damaged areas before applying RockSolid Textured Clear Topcoat.
CONCRETE PREPARATION – For coating over bare concrete
Scrub heavily soiled areas with RockSolid Heavy Duty Degreaser or Rust-Oleum Cleaner & Degreaser (sold separately). Scrub thoroughly, then rinse. Repeat as needed. Mix the concrete etch powder (sold separately) with 2 gallons of water until dissolved. (DO NOT add concrete etch directly to paint). The solution contains a mild citric acid. (DO NOT use muriatic acid).
Pre-wet entire floor using a hose; then remove pooled water. Use a plastic watering can to evenly distribute the etch solution over a 10’ x 10’ section of floor. Scrub vigorously with a bristle brush to loosen dirt and dust. Keep the section wet until it has been etched and rinsed; then move on to the next section.
Once completed, rinse and squeegee the entire floor to remove any traces of etch. DO NOT leave pooled water on the floor. Etch will not discolor driveways or harm grass or plants if rinsed thoroughly. Allow the floor to dry thoroughly. Rub your fingers over the dry floor. If dust or powder comes off on your fingers, repeat scrubbing and rinsing until the floor is clean. Note: If the floor is not thoroughly cleaned and rinsed, the coating may not adhere properly.
MIXING
MIX ONLY ONE POUCH AT A TIME. Both components and the environment should be pre-conditioned to a minimum of 40ºF (4ºC) prior to use. Be sure the air and surface temperatures are at least 5º above the dew point.
NOTE: RockSolid Textured Clear Topcoat must be applied within 7 days of the RockSolid Floor Coating.
Combine the two components by placing the pouch on the ground and rolling it from the part A side towards the part B side like a tube of toothpaste. This will create pressure in the part A side and force the middle seal to burst, allowing the two components to mix together. Thoroughly mix the materials by shaking the pouch back and forth and squeezing the edges and corners toward the center of the pouch. Mix for 2-3 minutes.
Once the material is thoroughly mixed, use scissors to cut a corner off the pouch. Pour the mixed material from the pouch into a roller tray.
APPLICATION
Apply only when air, material and floor temperatures are between 40-90°F (4-32°C) and the relative humidity is below 80%. Extreme cold application temperatures may slow the cure time. DO NOT apply the coating if temperatures are expected to drop below 40°F for 48 hours after the application.
Use a ¼” nap roller cover (included) and 9” roller frame to apply a thin coating evenly to the floor in 5’x5’ sections in an “M” and “W” pattern. De-lint the roller cover prior to application. Trim the edges as you go using the 3” paint brush.
Continue working in 5’ x 5’ sections. Occasionally stir or shake pouch to keep the product well mixed. Keep a wet edge to prevent lap marks or sheen differences. Only one coat is necessary over a coated floor (two coats are required when applying over bare concrete). Do not coat over control joints or roll over control joints. Use a flexible control joint fill material if desired. Repeat the above steps for each additional pouch.
COVERAGE RATE
Coated Concrete: Each Polycuramine pouch covers up to 200-250 square feet. Two pouches will cover up to 450-500 square feet (2.5 car garage).
Bare Concrete: Two pouches will cover up to 200-250 square feet with 2 coats. Coverage may vary based on condition and porosity of the concrete.
DRY TIME
Temperature and humidity may affect drying time. Do not walk on the coating while it is still tacky. The surface should be ready for foot traffic in 8-10 hours and vehicle traffic in 24-36 hours, depending upon temperature and humidity.
CLEAN-UP
Clean tools and equipment with mineral spirits. Allow unused product to harden in the container and discard according to local regulations.
LIMITATIONS
This product must be installed at the specified spread rates to perform as described. Do not apply in direct sunlight. Do not apply product when the substrate and ambient temperatures are steadily below 40°F (4°C).
SHELF LIFE AND STORAGE
Sixty (60) months in factory delivered unopened pouches. Keep away from extreme heat, cold and moisture. Maintain at a proper storage temperature of 45-90°F. Keep out of direct sunlight and away from fire hazards.