READ ENTIRE LABEL BEFORE APPLYING
DESCRIPTION AND USES
RockSolid® Universal Base Floor Coating Kit is an odor free, clear Polycuramine base that serves as the foundation of four RockSolid floor finishing systems which includes Rich Solids, Metallic, Pearlescent and Marble Additives. Polycuramine provides excellent abrasion and chemical resistance. It combines key attributes from multiple chemistries into one system that is self-leveling, flexible, fast curing and high gloss. RockSolid Polycuramine is designed to be applied over interior concrete surfaces. The surface should be free of loose particles, rust, oils and contaminants.
PRODUCT FEATURES
- Low odor and can be applied indoors
- Formulated without the addition of VOC containing
solvent - Patented Burst Pouch Technology (Two part Burst
- Pouch Technology U.S. Patent Number 8,381,903 B2)
- 96% solids formulation
- Longer pot life than other 100% solids epoxies
- Has excellent self-leveling properties
- 7 day recoat window without sanding
- Excellent durability in a single coat
- 24 hour drive on time depending on temperature and humidity
SYSTEM REQUIREMENTS
- Universal Base
- Rich Solids, Metallic, Pearlescent or Marble Additive
- High quality 3/8” nap roller or Marble Roller & Tray Kit
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING PROJECT
SURFACE PREPARATION
Moisture Testing - New concrete should be allowed to cure for 30 days before application of any coating. If there is any doubt about the dryness of the concrete, conduct a test by simply taping a piece of 4 mil plastic sheet 18x18” on the bare concrete for 24 hours. Be sure to tape all four sides. After 24 hours, check the concrete for signs of moisture. The concrete substrate will be darker if damp. If moisture is found, allow additional drying time (10-14 days) and repeat the test.
Testing for Sealer - Check for curing compounds or other types of sealers by pouring a small amount of water onto the concrete. If water soaks in, the surface is suitable for coating. If water beads up on the concrete, the surface is not porous and a test application is warranted to ensure proper adhesion will develop. Sanding or mechanical abrading may be required if proper adhesion does not develop. Or use Rust-Oleum® Garage & Concrete Floor Primer (sold separately).
Previously Coated Floors - Previously coated floors need to be in good condition with proper adhesion to the concrete substrate. Check the adhesion of the previous coating by cutting a small X in the coating using a sharp razor knife. Firmly apply a piece of 5” duct tape over the center of the X cut, and then pull off with a fast snap. If more than 10% of the taped area is removed, the original coating is not bonded well and needs to be removed chemically or mechanically with a grinder. For best adhesion, scuff sand previously painted or coated floor using 80 grit sandpaper and clean with solvent such as acetone. Or use Rust-Oleum Garage & Concrete Floor Primer (sold separately).
Proper surface preparation is critical to achieve best results. Scrub heavily soiled areas with Rust-Oleum Heavy Duty Degreaser or Rust-Oleum Cleaner & Degreaser (sold separately). Scrub thoroughly, then rinse. Repeat as needed. Use the supplied RockSolid concrete etch per the instructions to provide the proper surface condition to ensure proper adhesion. Rinse the floor thoroughly and allow it to dry completely
MIXING
MIX ONLY ONE POUCH AT A TIME. Both components and the environment should be pre-conditioned to a minimum of 40ºF (4ºC) prior to use. Be sure the air and surface temperatures are at least 5º above the dew point.
Place a tarp on the ground and thoroughly mix the material in the pouch by shaking it both up and down and back and forth and squeezing each side of the pouch. Any clumps need to be massaged to break them up to ensure proper blending.
Combine the two components by placing the pouch on the ground and rolling it from the part A side towards the part B side like a tube of toothpaste. This will create pressure in the part A side and force the middle seal to burst, allowing the two components to mix together. Thoroughly mix the materials by shaking the pouch back and forth and squeezing the edges and corners toward the center of the pouch. Mix for 2-3 minutes.
Mix only one pouch at a time. The product is now activated and must be applied within 45 minutes to 1hour.
See application instructions for the specific system that was chosen. (Rich Solids, Metallic, Marble or Pearlescent)
APPLICATION
Apply only when air, material and floor temperatures are between 40-90°F (4-32°C). Optimal installation temperature is 55-90°F (13-32°C). Extreme cold application temperatures may slow the cure time. Do not apply in direct sunlight. Do not coat the floor if it is raining or if extremely damp conditions exist. The concrete surface must be completely dry at the time of the application to achieve proper adhesion.
COVERAGE RATE & DRY TIME
Dry times and coverage rates will be determined by the specific system used for the application.
CLEAN-UP
Clean tools and equipment with mineral spirits. Allow unused product to harden in container and dispose according to local regulations.
LIMITATIONS
This product must be installed at the specified spread rates to perform as described. Do not apply in direct sunlight. Do not apply product when the substrate and ambient temperatures are steadily below 40°F (4°C).
SHELF LIFE and STORAGE
Sixty (60) months in factory delivered unopened pouches. Keep away from extreme heat, cold and moisture. Maintain at a proper storage temperature of 45-90°F. Keep out of direct sunlight and away from fire hazards.