READ ENTIRE LABEL BEFORE APPLYING
DESCRIPTION AND USES
Rust-Oleum HOME Countertop Coating is an extremely durable, easy to use, revolutionary technology that allows you to coat over a wide variety of countertops without stripping, sanding or priming. Transform outdated countertops in 2 steps - simply clean, apply the required Base Coat + Top Coat system for a brand new look to your space.
Great for any bare, stained, sealed or previously coated countertop surfaces such as outdated laminate, ceramic tile, porcelain tile, melamine, wood and much more.
PRODUCT FEATURES
- 2 Step System
- No stripping, sanding or priming
- Superior adhesion to tough surfaces
- Maximum wear & stain resistance
- Full use after 24 hours
KIT CONTENTS:
1-Quart Countertop Base Coat
1-Quart Countertop Satin Top Coat
1-4 oz. Heavy-Duty Cleaner
1-4 oz. Gray Marble Veining Paint (with Ultra White Marble kit only)
NOTE: White Tint Base can be applied as is for Ultra White or tinted prior to application. Two base coats are required when applying the White Tint Base in Ultra White. Deep Tint Base must be tinted prior to application.
OTHER SUPPLIES NEEDED (not included in kit):
3/8" Nap Roller Sleeve
1/4" Nap Roller Sleeve
Roller Frame
Painter's Tape
Paint Tray
Bristle Brush
Artist Brush (for marble kit only)
Mist Bottle (for marble kit only)
Tack Cloth
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING PROJECT
IMPORTANT: All countertops should be tested for adhesion before coating the entire surface. Clean a small 3”x3”, inconspicuous area, let dry. Apply base coat over area and allow to dry for 12 hours. Take a utility knife and make an “X” in the coating down to the surface. Apply a 4” piece of duct tape over the “X” and press firmly. Remove the tape with one quick pull. If more than 10% of the coating comes off, the countertop will need to be sanded with 60-80 grit sand paper before coating the entire surface. After a successful adhesion test, lightly sand test area before fully coating.
SURFACE PREPARATION
Rinse or wipe away any dirt and dust. Clean the countertop with the 4 oz. cleaner included with the kit or a cleaner degreaser, such as Original Krud Kutter® Cleaner Degreaser. Rinse thoroughly and allow to dry completely. For any areas where caulk is present, caulk needs to be removed before applying coating.
NOTE: Failure to follow this preparation method may result in poor adhesion and possible coating failure.
SYSTEM APPLICATION
Rust-Oleum HOME® Countertop Base Coat is ready to use. Do not thin. Stir thoroughly prior to use. If using more than one can of Base Coat, intermix cans together for color uniformity. Apply when air, material, and surface temperatures are between 50-90°F (10-32°C) and relative humidity is below 85%. Use a high-quality bristle brush or edger to trim the perimeter and hard-to-reach areas. Use a high-quality, 3/8” nap roller cover to apply an even coat onto the surface.
STEP 1: Apply Countertop Base Coat in 2’x2’ sections, and maintain a wet edge while rolling. Do not let product puddle. Only one coat is recommended.
*NOTE: For White, 2 coats are required. After coating the countertop, wait 4 hours before applying second base coat or applying any necessary touch-ups. Let touched-up areas dry for 1-2 hours (dry to touch) and then top coat can be applied.
OPTIONAL/MARBLE VEINING STEP: Once base coat is completely dry, additional Rust-Oleum HOME® coatings, such as the Gray Marble Veining Paint, can be applied to create a designer look. Be sure to follow the on bottle coating instructions and ensure the surface has thoroughly dried and is dust-free before applying the top coat (Step 2).
STEP 2: Apply Rust-Oleum Home® Countertop Top Coat. The Countertop Top Coat can be applied 4 hours after initial base coat application. Do not thin. Stir thoroughly prior to use. Apply when air (ambient) temperature is 50-90°F (10-32°C) and relative humidity is below 85%. Use a high-quality bristle brush or edger to trim the perimeter and hard-to-reach areas. Use a high-quality, 1/4” nap roller cover to apply an even coat onto the surface. Apply in 2’x2’ sections, and maintain a wet edge while rolling. Do not let product puddle. Only one coat is recommended. If a second coat is desired for additional durability or uniformity, wait until the first coat is dry to touch (1-2 hours) before applying, but must apply within 24 hours. For vertical application, apply Countertop Top Coat in two thin coats.
IMPORTANT: Rust-Oleum HOME Countertop Base Coat and Topcoat are required for the project.
DRY & TOPCOAT TIMES
For full system, allow 24 hours for light countertop use. Allow 72 hours before replacing large or heavier items (avoid dragging). Full cure is 7 days. Do not clean before 7 days.
CLEAN UP AND STORAGE
Wash tools and equipment with warm water and a mild detergent. Dried product remove with lacquer/thinner. Protect unused product from freezing. aner.
LIMITATIONS
Not for use on exterior spaces. Not for use on interior surfaces that are sealed with a superhydrophobic sealer. Not intended to be used as a food preparation surface.
USAGE
Surface Protection: As with most manufactured laminate and countertop surfaces, this paint finish will remain durable with proper use and care. Use a trivet or other protective material underneath all hot cookware and heated objects. Use cutting boards or other protective surfaces when preparing food. Heavy pounding, knives or other sharp utensils may scratch the surface. Do not allow water to pool for extended periods, clean up hot grease and any spills with a cloth or non-scratch abrasive pad.