DESCRIPTION AND USES
Zinsser Ceiling Paint – Paint & Primer in One is a high performance, low VOC, acrylic paint specifically designed for ceilings. Ceiling Paint – Paint & Primer in One has excellent stain blocking resistance and seals water and other household stains in one coat. Ceiling Paint & Prime in One goes on pink and dries to a bright white finish which is mildew resistant.
Ceiling Paint – Paint & Primer in One can be used on new or previously painted or primed wood, drywall, painted metal and plaster, textured and popcorn style ceilings in kitchens, bathrooms, basements, closets and other living areas. Bare metal, new or knock-downed texture should be primed and sealed with Bulls-Eye 1-2-3 Primer. If unsure about the integrity of the surface, test adhesion by placing a 2” piece of adhesive tape on the ceiling and snap pull it off. If tape removes remnants of the ceiling, the ceiling needs to be primed first. Seal popcorn ceilings with Cover Stain Primer before applying Ceiling Paint – Paint & Primer in One.
PERFORMANCE CHARACTERISTICS
• High hiding, high performance, no spatter formula
• Color changes to show coverage – applies pink, dries bright white
• Mold & mildew resistant finish
• Dries in less than 1 hour
• Water clean up
PRODUCT APPLICATION
SURFACE PREPARATION
Clean the ceiling surface with a damp cloth to remove any dirt, dust, soap film and other surface contaminants. Remove grease, oil, wax and wallcovering adhesive with Zinsser Adhesive Remover. Use Jomax Mold & Mildew Stain Remover to clean and remove mold and mildew stains. Remove loose paint and abrade glossy surfaces by sanding or scuffing. Patch all cracks and holes with Zinsser Ready Patch Patching Compound. Countersink all nail heads and sand smooth. For severe stains use Bulls-Eye 1-2-3 Primer.
APPLICATION
Apply only when air, material, and surface temperatures are between 50-90°F (10-32ºC) and the relative humidity is below 85%. Thoroughly mix to ensure any settled pigment is re-dispersed before using. Apply at package consistency. Do not thin for one coat coverage. In most cases only one coat is necessary. If excessive absorption occurs over very porous substrates, a second coat may be necessary. Apply generously and avoid overspreading. Provide adequate ventilation and warmth for normal drying. Product is designed to go on with a pink color to easily identify missed or skipped spots. As the paint dries, it will change to the intended bright white ceiling color.
Apply with a quality ½” nap roller or a nylon or polyester brush. Prepare the roller or brush by dampening it with water. Brush a 3” or 4” border around the edge of the ceiling. Start with a short dimension of the ceiling. Apply a strip of paint at one end of the room and continue until the first strip reaches the end of the room. Go back to the starting edge and paint another strip parallel to the first working gradually over the entire length of the room. Repeat until the ceiling is finished. An extension pole is recommended for making longer strokes.
An airless sprayer may also be used. Follow the manufacturer's instructions when using spray equipment. For airless spraying use a 0.017” to .0.019” tip at 2000 to 2500 psi. Wear NIOSH approved respirator and provide adequate ventilation.
DRY TIME
Ceiling Paint - Paint & Primer in One dries in 1 hour or less. Thick films, poor ventilation, cool temperatures or high humidity may increase the time for the color change to take effect. Hot and dry conditions or a porous surface may accelerate the color change.
CLEAN-UP
Clean hand and application tools with warm soapy water. Wipe up spills immediately with a clean damp cloth. Painted surface may be washed after 30 days with a mild detergent and cellulose sponge. DO NOT USE HARSH ABRASIVE CLEANERS. Re-wetting the dry paint film before 30 days may cause the pink cast to reappear. This will dissipate with drying. After 30 days cure time, the condition should not reoccur upon re-wetting. Follow equipment manufacturer’s directions to clean spray equipment. Dispose of unused or unwanted product in accordance with local laws regulating water-based coatings.