DESCRIPTION AND USES
RockSolid Color Enhancing Sealer is a penetrating sealer that protects concrete and masonry surfaces from the damaging effects of water, salt and chemicals, and enriches the appearance of colored pavers, brick, and porous natural stone without adding gloss. This water-based, hydrophobic formula provides a "breathable" protective barrier to keep water out, protect against stains, and extend the life of your concrete and pavers. The color-enhanced, "natural look" matte finish is suitable for use on driveways, patios, walkways, pool decks and more.
Use on interior or exterior, bare concrete and masonry surfaces. Do not use on asphalt or garage floors. It is ideal for driveways, walkways, porches, pool decks, basements and more. This product is not for use on previously sealed, painted or stained floors or over loose or poorly cured concrete.
Once sealed, the surface is no longer paintable. For ongoing maintenance, surfaces previously sealed with RockSolid Color Enhancing Sealer (or another water-based penetrating concrete sealer) may be sealed again with this product.
PRODUCT FEATURES
- Ready-to-use water-based low VOC penetrating sealer
- Enhances new or faded surfaces
- Seals and protects the surface
- Resists chemicals and stains, chloride salts, and high alkalinity
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING PROJECT
SURFACE PREPARATION
Proper surface preparation is critical to achieve best results. Allow newly poured concrete to cure for a minimum of 28 days. The sealer must be able to penetrate into the surface. Sprinkle water on the surface and if the surface turns dark with the water, the sealer can be applied. Sweep away all loose dirt, debris and remove any vegetation that could interfere with application and performance. If necessary, use a wire brush or sander to remove any loose or unsound concrete or masonry. Remove any efflorescence with RockSolid Efflorescence Remover. Clean the entire surface, including any oil or grease spots with RockSolid Heavy Duty Cleaner or Rust-Oleum® Cleaner & Degreaser (sold separately). Scrub the surface with a stiff bristle brush or broom. Rinse thoroughly with fresh water, preferably with a power washer.
Repeat as necessary to completely clean and rinse. Allow washed surfaces to dry at least 24 hours prior to application. A dry substrate is required to achieve proper penetration. In climates where freezing temperatures have existed prior to application, allow adequate time for surfaces to thaw. Test in a small area to confirm desired result before completing project. Degree of color enhancing will depend on surface type. Dense or wet-cast surfaces such as concrete floors may show minimal color enhancement.
APPLICATION
RockSolid Color Enhancing Sealer is ready to use. Do not thin. Use only when air (ambient) temperature is between 50-90°F (10-32°C) and the relative humidity is below 85% during the day and night. Do not apply in direct sunlight. Do not apply if rain is expected within 24 hours. Use in a well-ventilated area. Avoid applying late in the day when temperatures are falling as the formation of dew can interfere with proper sealing.
Mask adjacent surfaces to allow spray application up to all edges. Protect delicate foliage from overspray. Apply using a standard pump sprayer with an adjustable spray tip or apply using a standard ⅜” nap roller. Choose the best applicator for the size of the project and texture of the concrete. Do not pour the sealer directly on the surface or allow to puddle.
Stir the container to mix product. Fill pump sprayer with product, then fully pressurize the sprayer. Set the spray tip to a medium-fine mist and spray 10-12” from the surface. Start and stop the sprayer just off the work area to prevent drips. For larger areas, work in 6’x6’ sections at a time before moving to the next section. Apply the product evenly, using a circular or oval pattern to saturate the surface. Do not allow the sealer to puddle. Apply sufficient product so that the surface remains wet for several minutes before it is absorbed. After 5-10 minutes, back-roll any remaining puddles/pools using a ⅜” nap roller to prevent excess material from drying on the surface. Material that is not absorbed should be backrolled or brushed out to avoid build up. A second coat may be applied to maximize protection while the first coat is still damp (wet-on-wet). Protect shrubbery, plants, grass, glass, metal and asphalt surfaces during application.
Once sealed, it is no longer a paintable surface. For ongoing maintenance, surfaces previously sealed with RockSolid Penetrating Concrete Sealer (or another water-based penetrating concrete sealer) may be sealed again with this product.
COVERAGE
Each gallon covers approximately 250 square feet (single coat). Coverage will vary depending on the texture and porosity of the surface. Porous surfaces may require multiple coats. A second coat can only be applied while the first coat is still damp.
DRY TIME
Dry time is based on 70°F and 50% relative humidity. Allow longer dry time at lower temperatures and higher humidity. Wait a minimum of 4-6 hours for light foot traffic. Wait 24-48 hours before returning heavy items, furniture and vehicles. The surface will be fully cured in 72 hours.
CLEAN-UP
Soap and water. Clean drips, runs and over-spray residue while still wet. Dried material may require mechanical abrasion to remove. Clean application and spray equipment with detergent and water immediately following use. Properly dispose of all soiled rags, roller covers and unused product.
KEEP FROM FREEZING WARNING! KEEP OUT OF REACH OF CHILDREN